IN-HOUSE FABRICATION
Architectural Sheet Metal
Custom copings, fascia, edge metal and flashings are fabricated in-house to protect vulnerable transitions and complete the roof system properly.
TRUSTED BY
The Details That Decide Whether a Roof Lasts.
Most commercial roof failures do not start in the membrane field. They start at the edges, the penetrations, and the transitions — the copings, counterflashings, gravel stops, and gutters where water is funneled and where artistry is tested. Architectural sheet metal is the discipline of getting those details exactly right, and it is one of the things that separates a roof that lasts from one that leaks within a few seasons.
AVID Roofing & Waterproofing brings decades of fabrication and installation experience to this work. Our field operations and estimating leadership bring a combined 205 years of experience across the trade. That experience shows most clearly in the metal — the components that have to be measured, formed, and fitted to a specific building rather than pulled off a shelf.
Sheet metal is also where the wind takes a roof apart. In a high-wind event, uplift concentrates at the perimeter — the edges and copings. Metal that is properly fabricated, fastened, and detailed holds the membrane down; metal that is not becomes the failure point that peels a roof open. This is why insurers and code officials scrutinize edge metal after a storm.
Fabricated To The Building, Not To A Catalog.
Our process starts with measuring and assessing the actual conditions — the deck, the parapet walls, the edge profiles, and how water is meant to move across and off the roof. From there, we fabricate metal components to match, whether that is custom coping to cap a parapet, edge metal to terminate a membrane cleanly, or scuppers and collector heads sized for the building's drainage load.
Precision matters because metal is unforgiving. A coping joint that is fractionally off, a flashing that is not properly lapped, an edge that traps rather than sheds water — each becomes an entry point. We fabricate and install to tolerances that close those gaps.
We fabricate from quality material in gauges and finishes suited to the application and the North Texas climate, and we install with attention to expansion, fastening, and lapping — the details that determine whether metal performs for decades or corrodes and loosens in a few years.
What You Get And The Failures You Avoid.
You get sheet-metal components engineered and installed to protect the roof's most vulnerable points: wind uplift at the perimeter, water intrusion at penetrations and transitions, and slow corrosion that undermines poorly specified metal. Properly detailed edge metal also satisfies wind-rating requirements that adjusters and code officials review after a storm.
The risk we mitigate is the one owners rarely budget for — a brand-new membrane undone by an edge detail nobody scrutinized. Strong metalwork protects the larger investment around it. You also get metal that satisfies the wind-uplift and code requirements your building is held to, documented in a way that supports both warranty and any future claim.
You also get the assurance that the most failure-prone parts of your roof were handled by people who understand them as a specialty rather than an afterthought. On most projects, the metal is where corners get cut because it is hidden in the scope; with us, it is itemized, scrutinized, and built to last.
Logistics and Continuity.
Fabrication and installation are sequenced to the larger project timeline so metal arrives when the roof is ready for it, not before. For occupied buildings, we stage material deliveries and rooftop work to minimize disruption to tenants and operations.
Because the same firm fabricates, installs, and warrants the work, there is no handoff gap between the people who made the metal and those who installed it on your building.
Because metal is custom to each building, lead time matters. We measure early and fabricate on a schedule that keeps the overall project moving, so the metal never becomes the bottleneck that stalls a reroof.
Architectural Sheet Metal Frequently Asked Questions:
Architectural sheet metal refers to the custom-fabricated metal components that protect transitions, edges, and penetrations on a commercial roof — including copings, fascias, gravel stops, gutters, downspouts, expansion joints, and custom flashings. These aren't decorative; they're critical waterproofing elements at the most vulnerable points of any roofing system.
Most commercial roof failures don't happen in the membrane — they happen at the edges. Wind uplift concentrates at the perimeter, and poorly fabricated metal is what peels a roof open. One bad coping joint or flashing detail can fail the entire system. Metal has to be custom-measured and fitted to your building, not pulled off a shelf. Get the edges right the roof survives. Ignore them, and you've sabotaged a $300K investment.
We fabricate and install coping caps, fascia systems, gravel stops, gutters, downspouts, scupper boxes, through-wall flashings, expansion joint covers, and custom penetration flashings. Our team includes sheet metal specialists, not just membrane roofers — the same crew that installs the roof handles the metal.
Yes. Sheet metal work is system-agnostic — it's designed to the specifications of the membrane being installed, whether that's TPO, PVC, modified bitumen, EPDM, or metal panel. We detail the metal to the manufacturer's specs to keep warranties intact.
Properly fabricated and installed commercial sheet metal — typically 24-gauge steel, aluminum, or copper — lasts 30 to 50 years. The metal itself is rarely the failure point. Issues almost always stem from inadequate fastening, improper laps, or unmaintained sealants.
Yes. Coping failures, separated gutters, rusted scupper boxes, and deteriorated fascia systems are all common repair items we handle independently of a full reroof. If your sheet metal is failing and the membrane underneath is still sound, targeted metal repair is the right call.